pig-monkey.com - fire

Fire Starting with the Trail Designs Ti-Tri Inferno

2011-07-29T00:00:00-07:00

On our last morning in the Red Buttes Wilderness, Avagdu and I woke up to a very wet camp. We wanted fire, but neither of us had brought any dry wood into our shelters the night before. Everything was soaked.

We gathered what we could – branches from dead fall that were up off the ground, as well as dead lower branches from standing trees – but the trees were so sparse in the area that, even after splitting, much of this wood was still wet. (I should mention that we wanted a fire, but did not need one. I, at least, was not hugely motivated to put a large amount of energy into batoning. So a small amount of our failure ought to be attributed to laziness.)

After failing to get a blaze going with the wet wood, even after using a bit of inner tube to extend the flame, I hit on the idea of using the Inferno.

I’ve had my Trail Designs Ti-Tri for two and a half years now. It’s been my primary stove system for all of that time. Last Fall, I contacted Trail Designs and had them send me an Inferno insert for the system. The Inferno consists of a second, inverted cone and a grate. The grate raises the base of the fire up off of the ground, allowing for an improved air flow, and the second cone creates a double-walled stove. This turns the Ti-Tri into a wood gassifier, similar to the Four Dogs Bushcooker or the ever-popular Bushbuddy.

So, back at camp, I thought the Inferno might help. I had never used it before solely to start a camp fire, but I knew from previous experience using it to cook my dinner that it was efficient enough to burn damp wood. It would give us a raised platform, allowing us to build the fire up off of the saturated ground, and the cone would provide a wall to keep the heat in and help dry the wood.

It was a success.

We split a bit more wood, and did a bit more feathering. It was all still as damp as before, but shortly we achieved a small blaze inside the Inferno. From there, it was simply a matter of building the fire up and around the Inferno. With the heat put out by the cone, even the wet, unprocessed wood would dry and burn. As the fire built up, the Inferno could be pulled out with a multi-tool or a couple sticks, and packed away with the rest of the Ti-Tri, ready to cook the next meal.

The weight of the Inferno insert varies. It is dependent on the size of the outer Caldera cone, which in turns varies based on the size of the pot. For my system, which is built around a 900mL pot from Titanium Goat, the pieces that comprise the Inferno weigh in at a collective 38 grams (1.34 ounces). Given that it not only increases the Ti-Tri’s efficiency as a wood burning stove, but also functions as an emergency fire starter, I’m happy to haul the extra weight.

Gear List

2010-08-29T00:00:00-07:00

I’ve had a few requests to do a gear list for some of my recent trips. Since it’s been over a year since the last one, I thought I would acquiesce. What follows is the list from my recent journey to the Goat Rocks. Though that was a short trip, my gear has varied very little on any trip this year. I’ll take warmer clothing earlier (and later) in the year, and of course the amount of food varies based on the length of the trip, but most everything else remains static. This is quite the change from even just a year ago, where it seems like my gear would change drastically from trip to trip! Perhaps I know what I’m doing a little better now.

Some of the gear is light, some of it isn’t. Regular readers know that I always struggle to find a balance between lightweight, functionality, and durability. Certain items that I carry – like, say, the saw – are not likely to be found in the pack of an average backpacker, but are suited to my method of travel. In all, my base weight for this trip was right at 20lbs. I’m not too ashamed of that. In fact, considering that my pack alone weighs 6lbs when empty, that base weight is pretty darn good.

If you have any questions or comments about the items, feel free to get in touch.

Packed

Kifaru ZXR
- Sea to Summit Ultra-Sil Dry Sack (13 liter)
  - Kifaru 20F Slick Bag
  - Coccoon Silk Mummy Liner
- Sea to Summit Ultra-Sil Dry Sack (8 liter)
  - Ex-Officio Boxer Briefs
  - Fox River AXT Wick Dry Off Road Crew
  - Ibex Woolies Bottoms
  - Icebreaker L/S Inca
  - Bandana (22" x 22", cotton)
  - Montbell U.L. Down Inner Jacket
  - MSR Packtowl UltraLite (large)
- Mountain Laurel Designs Spintex EXP Stuff Sack (XLarge)
  - LOKSAK OPSak (20 x 12.5)
    - 4 days of food
  - REI nylon mesh bag (5" x 6")
    - Mountain Laurel Designs Super Glide Bear Bag Line
    - Mountain Laurel Designs SuperFly Mini Biner
- Mountain Laurel Designs Silnylon Stuff Sack (8" x 12")
  - Outdoor Research Rocky Mountain High gaiters
  - Marmot Precip Full-Zip pants
- Gatorade Bottle
- 2+L Platypus w/ hose, mouthpiece, and bite valve cover
- Cut down Platypus scoop
- 2x ~25ft paracord
- Stake bag
  - 4 Durapegs, 2 Eastons, 2 X-pegs, 2 Nite-Ize Figure 9s
- Kifaru Paratarp
- Black Diamond Alpine Light Carbon Cork Trekking Poles
- Kershaw Folding Saw
- Barefoot Ted custom huaraches
- Kifaru Ultralight PullOut (small)
  - Aquamira water treatment chemicals (liquid)
  - Platypus Pre-Filter
  - Sawed-off toothbrush
  - Small travel floss
  - 1 oz All-Terrain Weathershield (SPF 30)
  - 0.5 oz Dr. Bronner's Peppermint soap
- Reflectix sit pad
- Trail Designs Ti-Tri with 900mL pot and accessories
- Therm-a-Rest Z-Lite
- TAD Gear BC-8
  - Silva Ranger CL compass
  - ACR Whistle
  - MapTools.com 1:69,500 Grid Tool
- Outdoor Research Foray Jacket
- Kifaru PackLock Windshirt
Kifaru Longhunter Lid
- Shoulder strap
- 1 quart ziploc
  - Toilet paper
  - 1 oz Hand sanitizer
- Emergency fire kit
- First aid kit
- Kifaru Ultralight Pullout (small)
  - REI Keychain Thermometer
  - K & M Industries Match Case
  - Croakies Glasses Retention Lanyard
  - Jetstream ballpoint pen
  - Sharpie
  - Highlighter
  - #2 Pencil
  - All-Terrain Lip Armor (SPF 25)
  - 4x safety pins
  - Duct tape (length unknown, .75" diameter roll)
  - StickPic #3
  - Badger Healing Balm
- Sea to Summit Headnet
- Petzl Tactikka headlamp
- Tyvek Stuff Sack
- Rite in the Rain No. 393-M
- Large garbage bag
- 1 quart ziploc
  - 3x Green Trails maps
- Plastic vial-type container (found on street)
  - 16x cotton balls w/ petroleum jelly
- Hard glasses case (unknown brand/model)
  - Oakley soft lens cloth bag
  - Julbo Micropores (Rx)
- Sea to Summit Ultra-Sil Dry Sack (2 liter)
  - Bandanna (22" x 22", cotton)
    - Canon Powershot SD1000
  - Spare camera battery
  - Joby Gorillapod

On Body

Smartwool Medium Hiking Socks
Railriders Weatherknickers (old Weatherpants cut to knicker length)
- Patagonia Friction Belt
  - TAD Gear S1 Sheath
    - Leatherman Blast
  - Mora Carbon #1 (w/ modified sheath)
- Snot rag (22" x 22" cotton bandanna)
- Rubberized BIC lighter
Mountain Hardwear Canyon Shirt
Buff
Boonie hat
Lowa Renegade II Gtx boots
- Sole Ed Viesturs Ultra footbeds
Luminox 3001 watch w/ Maratac Bond Regimental NATO band
- Suunto Micro Clipper Luminous compass
Paracord necklace
- Nemesis Hellion
- Ferrocerium Rod
- Photon Freedom Micro LED

(I do hope that I haven’t forgotten anything. If you notice anything conspicuously absent, please let me know!)

Romani Fire Starting

2010-06-24T00:00:00-07:00

This past week I read Dominic Reeve’s Smoke in the Lanes. The book is a first-hand account of the lives of Romani in England during the mid-1950s, which marked the end of the era of horse-drawn wagons. It’s an interesting read if you’re at all interested in itinerant lifestyles.

Toward the end of the book the author describes lighting his daily fire in very wet conditions:

Nobody had collected any wood for the morning's fire, so I scrambled into the middle of a tangle of thorn-bushes, the limbs of which were heavy with rain that showered down on me; and within a matter of minutes I was completely soaked. I did not possess a raincoat and my old jacket and cord trousers were inadequate to withstand the water. Nevertheless, I managed to gather quite an imposing amount of dead wood, all sodden, and I returned with it to the site of the previous night's fire. I took a stump of candle from my pocket and broke it in half, then I lit one half and set it upright in the watery ashes, piling some twigs and small wood round and above it. When I had placed sufficient twigs above the tiny flame I laid the other half of the candle stump in the wood directly above the flame so that the heat from below gradually rose upwards, melting the wax which then caught fire and ignited the soggy twigs. It is an old Romani trick, and a very successful one.

Le Loup often talks about carrying a beeswax candle in his 18th century fire kit. I always assumed that this would be used to keep a flame below damp tinder to dry it out, similar to how today we might take advantage of the long burn time of cotton balls soaked in petroleum jelly to light slightly damp materials. It never occurred to me to break the candle in two and melt the second half above for even more heat. Neat trick!

None but the Romanies, or perhaps the few remaining tramps, can know how great a comfort is afforded by a fire. Once its warming tongues lick upwards into the pile of sticks and one's tingling, numbed fingers are eased in its glow, one experiences great pleasure and satisfaction. It is a creative, aesthetic, pleasure. On countless grey winter mornings, often in company with other travellers, I have sat huddled close to an immense [fire], my front glowing and steaming with heat and my back running with rain or heaped with snow. The fire is everything to us. With it we can cook, eat, survive and live: without it we should perish.

Emergency Fire Starting Kit

2010-05-15T00:00:00-07:00

This kit is kept in the lid of my rucksack, which also functions as a man-purse for short trips away from camp. It is intended for emergencies only, and so is secondary (or even tertiary) to my normal fire starting equipment: ferro rod(s), rubberized BIC lighter, matches, and a fair amount of cotton balls covered in petroleum jelly. The kit here is to be used only when these other methods of starting fire have for some reason failed.

It is quite simple and is probably nothing unique. Everything is kept together and dry inside of a small aLOKSAK (measuring 5”x4”). It weighs 2.8 oz. The contents are as follows:

9 Tinder Quik tabs
6 Ultimate Survival Technologies WetFire cubes
16 REI Storm Proof Matches (sealed in a ziploc bag with two inner-tube ranger bands around the outside)
2 REI Storm Proof Matches striking surfaces (sealed)
Spark-Lite fire starter
Rubberized BIC lighter

That’s a whole lot of fires that I can start with just this small kit, and I don’t even have to start messing around with natural tinder or making char-cloth yet!

Previously the envelope held a small ferrocerium rod and striker in lieu of the Spark-Lite. I’ve never been too impressed with the Spark-Lites: the sparks produced are relatively small and weak. They are fine for starting a fire with prepared tinder such as cotton balls or those commercial products included in this kit, but trying to get a natural tinder to take with them can be a bit of a pain. As for the whole one-handed fire starting thing – well, I have never broken my arm or hand. I have been cold enough to not have the fine motor control needed to reliably operate a Bic lighter or Spark-Lite. So for me, given the choice between a normal ferro rod and a one-handed Spark-Lite, I’d go for the normal rod. It requires a gross movement that I know I can always achieve, even when cold.

I decided to remove the ferro rod and add the Spark-Lite to this kit because I figure that I have enough ferro rods stashed here-and-there (including at least one tethered to my body) that the chances of me losing all of them are very slim. (I would be more likely to lose this kit, which is kept in my pack, not on my body.) I should never have to depend on whatever spark-making tool I keep in the envelope, but by opting to make that tool a Spark-Lite, I do give myself the possibility of one-handed fire making (without depending on lighters or trying to light a match held in my teeth). Doug Ritter would be proud.

Simple Ferrocerium Rods

2009-12-06T00:00:00-08:00

I don’t like paying for brand-name ferrocerium rods with handles when blanks can be got for much cheaper – usually $5 less than their handled counterparts. But I do like to have a handle on the rod, and I require some sort of lanyard. When it comes to something as important as a ferro rod, I find comfort in knowing that it is secured to this-or-that.

The simplest solution is to tape a loop of paracord to one end of the rod. I use gutted paracord. The tape can be wrapped a few extra times to make a handle however thick I like.

The other rod in the above photo has a similar lanyard attached in a different manner. The paracord is first taped to the rod with a small piece of electrical tape. Then, on top of that, I slid a small piece of heat-shrink tubing (the kind used for electrical wiring). That was blasted with a hair dryer, causing it to shrink.

A small hole could also be drilled in one end of the rod. This is something of a fire hazard: the drill and rod will be throwing a whole lot of sparks as the drill works its way through. And it requires access to power tools, which isn’t always practical.

My favorite method is the tape. The lanyard is secure and the tape provides a thick, padded handle.

I like to buy my blanks from Ben’s Backwoods. If you like misch metal blanks, Going Gear is the place to be.

Mora Sheath Modifications

2009-12-05T00:00:00-08:00

The greatest disappointment about any Mora knife is the sheath: a flimsy, plastic thing that won’t easily fit on a decent sized belt and does not even hold the knife very securely. As they come, I consider them unusable. But a few simple modifications and additions make them quite acceptable.

The Mora knife sheaths are designed to be mounted either on a button on a pair of coveralls or through a belt. Apparently people wear very small, skinny belts in Sweden. Over here in the United States of Gun Belts, that doesn’t fly. The belt slot on the sheath can be forcefully enlarged by shoving in a piece of wood, such as a ruler, and applying heat to cause the plastic to expand, but I don’t trust that such an act will not over weaken the plastic. I’m not a big fan of carrying a Mora directly on my belt, anyway. Usually, I’ll carry the knife either on a lanyard around my neck or as a dangler off my belt. But both of these setups allow the possibility of the knife and sheath to swing freely, accentuating the problem of an insecure fit.

Both the problem of how to carry the sheath and the problem of the insecure fit can be addressed with a single piece of paracord.

With the knife in the sheath, I take a piece of paracord and run both ends around the handle and through the slot for the belt. Then, tight against the back of the sheath, I tie an overhand knot in either end of the cord. This creates a loop of paracord on the front of the sheath that can be made smaller, but cannot become any wider than the bottom third of the handle. Because the handles on Mora knifes are somewhat tapered – fatter in the middle than on either end – this loop prevents the knife from being removed from the sheath. Even if the knife is only lightly dropped into the sheath rather than securely pressed, it cannot be removed without first sliding off the loop of paracord.

After tying the two knots against the back of the sheath in either end of the paracord, I take both ends and tie them together, forming a loop on the back of the sheath. This provides my carry options.

If I want to wear the knife around my neck, I take a pre-tied loop of paracord that I carry and loop it through itself around the loop on the sheath.

To carry the knife in a dangler system, I prefer to use a Maxpedition Keyper rather than a carabiner. The Keyper is mounted on my belt and clipped into the loop of paracord on the sheath. (To reduce movement in this setup, I’ll stick the knife and sheath in my pocket.)

The last thing that I do to this part of the sheath is add a small wrap of electrical tape around the very top, covering the upper bit of the belt loop and the button hole. This prevents the paracord from sliding to the top of the sheath and forces the securing loop to be about .75” from the very end of the handle. I’ve found that if this is not done, the securing loop is like to slip off the handle.

That’s all that is needed to make the sheath usable, but a few other additions can be made to increase its utility.

Around the top of the sheath, I wrap tape. In the sheaths pictured here, one has 2” olive drab duct tape, the other has 1” black Gorilla Tape (which is like duct tape, but thicker and stickier). One can never carry enough tape. I imagine, also, that the tape likely increases the structural integrity of the sheath.

On the back of both sheaths, I have a #17 sailmaking needle, pre-threaded with black kevlar thread, taped down with some electrical tape. As I mentioned in my review of the RAT Izula, this is an idea I first picked up from one Dave Canterbury’s videos. The extra needle and thread adds no noticeable weight and could be a welcome addition to the sheath if you ever find yourself separated from your pack, with the knife and sheath as your only piece of gear.

The next modification on the body of the sheath was also inspired by Dave Cantebury. In another of his videos, he showed how he had layered different width pieces of inner-tube on a machete sheath to create pockets that could store small items, such as a sharpening stone and magnesium fire starter. With that in mind, I add a wide piece of inner-tube onto the middle of the Mora sheath (which also serves to cover and further secure the taped down needle). Then, on top of that, I put a skinnier piece of inner-tube. Slid between both pieces is a backup ferro rod. Because the rod has rubber below it and rubber atop, there is an incredible amount of friction. The ferro rod becomes difficult to remove. I have carried blank rods in these “pockets” and they have never fallen out. Still, I prefer to carry rods with a lanyard of some sort on them. I loop the rod through its lanyard around the paracord loop on the top of the sheath, guaranteeing that the rod is secured.

The sheath for my KJ #1 knife has only a ferro rod. That knife is carbon steel and can generate sparks off the spine. On the sheath for the larger SL-2, however, I have added a small striker slid between the two pieces of inner-tube on the back. The SL-2 is made of laminated steel, which is too soft to reliably produce sparks.

These modifications made to the Mora sheath help to secure the knife, allow for different carry options, guarantee a source of fire, and provide a needle, thread and tape for repairs. They turn what is otherwise a near useless sheath into a functional item worthy of being matched with the Mora blade.

(I also own a high-quality leather sheath made by JRE Industries for the KJ #1 knife. I tie a loop of paracord through the top loop of leather on the sheath so that the knife may be carried around the neck or on a dangler, similar to the modified plastic sheath. The leather sheath does not require a loop of paracord on the front to secure the handle. Nor does it need pieces of inner-tube to create a pocket for a ferro rod. The only thing that it lacks is a repair needle, but I have found that most tape does not adhere very well to leather, so I cannot stick one on the back.)

K & M Match Case

2009-12-02T00:00:00-08:00

The K & M Industries Match Case has long been considered one of the top waterproof match cases available. Each case is hand made in the Elk River, Idaho garage of Keith and Marge Lunders.

The match cases are available in either brass or aluminum and come in two different sizes. The standard length cases are 3 7/8”, designed to fit 2 3/8” strike-anywhere matches. The long length cases, measuring in at 4 1/4”, are designed for REI Storm Proof Matches. Aluminum cases are available in black, silver, green, or red.

Last winter, I bought a standard length, black aluminum case. It has been part of my wilderness EDC for close to a year.

Though I don’t always use them, I always carry matches into the wilderness, in addition to at least one BIC lighter and a multitude of ferro rods. Ferro rods are my primary means of starting fire – usually with some synthetic tinder, such as Vaseline soaked cotton balls. It’s also my primary way of starting my alcohol stoves. If I’m not having luck with the rod, or all my tinder is wet, I can move to a lighter or a match to get the fire going. I’ve also found that when it gets to about 20 degrees Fahrenheit or below, denatured alcohol does not like to take a spark – instead requiring a match or lighter to start my stove.

A lighter is of course the easiest way of starting a fire, but because I carry a BIC lighter, it is not always dependable. If it was submerged, it will need some time to dry out before working. If there are high winds, the flame will no doubt get blown out. I have previously carried waterproof, windproof butane lighters, but those seem to eat through the fuel way too fast to be practical wilderness devices. It is difficult to justify the huge price increase in one compared to a BIC lighter. The other problem with BIC lighters is that it can be hard to determine how much fuel you have left. You can judge the weight, shake it around next to your ear and listen, but it’s a rough estimate at best. That’s what I like about matches: you can count how many you have. For this simple reason, I am sometimes likely to go to my matches rather than my lighter when I need ready-made flame.

Carrying the aforementioned REI Storm Proof Matches also addresses some of the other concerns of the BIC lighter: they will light when wet (if lit and then submerged, they will quickly relight themselves after you remove them from the water) and are nigh impossible to blow out. This makes them a great emergency fire source, but, like the fancy butane lighters, are relatively expensive compared to standard strike-anywhere matches. Because of this, I carry both: normal strike-anywhere matches for general use and REI Storm Proof Matches for when the elements are against me. The REI Storm Proof Matches, being pretty darn waterproof, aren’t in much need of a waterproof case (I imagine that they will get soggy and useless if they’re kept underwater for a long period of time, but if you accidentally take a bath during a river crossing and crawl out within a couple minutes, the matches should be fine). Strike-anywhere matches, on the other hand, do need extra protection. Hence why I decided to start with the standard size K & M case.

All K & M match cases feature a unique closure system. The lid itself has two o-rings on it to prevent any water leakage (guaranteed to 2000 psi of water pressure). It’s not a screw on lid, but simply pressed onto the case. After the lid is on, you then twist the cap, which in turn twists and tightens the thin nylon lanyard around the body of the case, ensuring that the fit remains tight. Ingenious, simple, and effective.

The body of the case itself is about 3” (not including the cap). The bottom half is smooth, while the top bit is etched with a pattern that ensures a good grip can be had on the case, even when you and it are soaked.

The top of the lid sports a small Suunto compass for general direction finding, greatly increasing the utility of the item. This isn’t some cheap, $1 knock-off button compass, either. Suunto compasses can be depended upon.

The outer rim of the lid has been etched in the same manner as the top half of the body for grip, but the case also comes with a small protective piece of plastic that slides snugly over the lid, protecting the face of the compass. With this installed, you loose the extra grip on the lid. This may be a problem in some conditions.

The lanyard, after it does its thing tightening the lid, extends down past the body of the case for about 12”, terminating in a loop, which allows the case to be securely fastened to your person.

The inside of the lid is roughened, which is supposed to provide a surface for striking the matches. Perhaps I don’t know how to strike a match, but it’s never worked for me. In fact, as a general rule, I find strike-anywhere matches to actually be strike-anywhere-there-is-a-commercial-match-striking-surface matches. I never have luck attempting to strike matches on any old rough surface. But that’s not a problem: all REI Storm Proof Matches come with extra striking surfaces inside the box. They’re pretty heavy duty, work with all types of matches, and come sealed in plastic. I tend to collect them and stash them everywhere. For the K & M match case, I cut off a small piece that would fit on the bottom of the lid and super-glued it on. This guarantees me a working surface to strike my matches.

The rest of the striker I put back in it’s plastic cover and store in the body of the case, for use as a backup. The plastic prevents it from striking and lighting any of the matches.

Because of the striking surface on the lid, I store all the matches tip down, so that they won’t accidentally light and turn the case into a bomb. With the the extra striker stored, I can jam in about 25 matches, give or take a few. You could fit in more if you removed the striker. The match case is also a nice place to carry a pre-threaded needle or two for emergency repairs.

Around the outside of the case, I keep a length of that same 700x35 bicycle inner-tube that I have around my BIC and a couple of my Moras. The inner-tube, along with matches that are guaranteed to be dry, gives me a sure-fire method of fire starting.

Both the brass and aluminum cases sell for $19 each. That may seem like a lot of money for a simple match case, particularly when you can pick up a cheap-o plastic one for $1.75, but I think it is well worth the money. The brass case looks a lot nicer and is more durable, but is a good deal heavier than the aluminum.

Some day I would like to acquire one of the long aluminum cases for my REI Storm Proof Matches, even though it is not strictly necessary.

I also own a TAD Gear Life Capsule O.K., which makes a good match case. The TAD Capsule is equally waterproof and also includes a compass in one end (albeit a cheaper one), but because of the significantly increased weight of the TAD capsule over the K & M case, I think the K & M is a superior product.

Another review of the case, along with some discussion of matches, can be found at British Blades. I thought I remembered Schwert doing a review of the case on the now defunct Outdoors Magazine, but I cannot find it in the archives.

Rubberized BIC Lighter

2009-11-28T00:00:00-08:00

Here’s a neat trick I picked up from Dusty’s YouTube video. In the video, he shows how to use a couple of old bicycle inner-tubes to make a semi-waterproof pouch for a BIC lighter. That didn’t appeal to me too much: I always carry a BIC in my pocket and his idea added to much bulk for my liking. But, at the end of the video, he cut a smaller piece of inner-tube to make a sort of sheath for the lighter.

I thought that was a great idea. It gives you a nice, rubberized grip for the BIC and provides a simple way of always carrying waterproof tinder.

I’ve now cut off pieces from a 700x35 bicycle inner-tube and made this modification to all my lighters.

A Ride and Some Tea

2009-09-16T00:00:00-07:00

I went for a bike ride today, following a set of train tracks through the woods. Off to one side a small path led to a grassy clearing and this square structure. I stopped for a bit, processed a down log to start a small fire, and enjoyed a cup of kukicha tea while reading a book.

Wilted Nettle

2009-06-18T00:00:00-07:00

A lazy day of doing not much of anything sometimes makes me feel guilty. It requires that some evening activity take place – something which gives one the satisfactory feeling of accomplishing something of use during the block of waking hours. Today I chose to spend the evening in the woods. I thought I might practice some knife skills, or just sit and read a book. Arriving at my spot I was unpleasantly greeted by a thick swarm of mosquitoes, greatly annoying me and foiling my plans for peace. I decided to start a small fire with a bit more green wood than usual. The smoke from a fire usually drives mosquitoes away and the green wood would put out more smoke than dead wood. When I was out collecting wood, I noticed a large patch of Stinging Nettles in the gully below where I was. The two thoughts of Nettles and fire brought to my mind an episode of Wild Food where Ray Mears picked a few fresh Nettles and wilted them over the fire to neutralize their sting and improve the flavor. I eat a lot of Nettle raw, crushing the leaves to break the needles and get rid of the sting, but I thought I might try this new method.

After the fire was going (and the mosquitoes buzzing off elsewhere), I put a small measure of dead wood on a corner of the fire to get a bit more flame than the smokey green wood was providing. This accomplished, I went back to the gully to collect a few stalks of nettle and return them to the fire. It took only about 15 seconds of holding one plant over the flame for it to become limp and drooping. I tested it a bit with my fingers to see if the sting had been neutralized. It had. Tearing off a bit and munching it around a bit in my mouth, I was greeted by quite a surprise: these wilted Nettles were, without doubt, the best Nettles I had ever tasted, perhaps even being the best wild weed I had ever enjoyed! I ate about a dozen tall plants, until I was quite satisfied with my evening snack. Occasionally I would leave a stalk hovering over the flame a bit longer than needed, but that would impart to the leaves a slightly toasted flavor, which I also found to be agreeable.

I’ll certainly be enjoying wilted Nettles again. It’s a bit more trouble than just eating them raw, but, even on the move, it takes very little time to start a small fire and prepare a few picked plants in this way. The improved flavor greatly pays back the small investment in time.

Possibles Pouch

2009-06-07T00:00:00-07:00

My possibles pouch began as being simply a Doug Ritter Pocket Survival Pak. The Survival Pak comes in a waterproof envelope that is meant to be carried in a pocket. I prefer a belt-mounted solution, so I ditched the waterproof envelope and moved the contents to a TAD Gear SERE SP pouch. The SERE pouch has velcro webbing on the back, which allows it to be mounted to be mounted to any sort of belt or PALS webbing.

When using the possibles pouch, I’m often traveling with my Kifaru ZXR. The ZXR is built upon Kifaru’s WrapTech Plus Suspension system, one of the primary components of which is the belt. The belt is a very thick, wide belt that is designed to work with the anatomy of the body and allow the user to comfortable carry obscenely heavy loads. The design of the ZXR’s belt makes it unpractical to have many pouches mounted to your own pants belt. Because of this, I didn’t want to actually mount the SERE pouch to my belt itself, but instead mount it so that it dropped down a bit below my waist, thus not interfering with the ZXR belt. To accomplish this, I simply tied a short loop of paracord through the pouch’s webbing. To mount the pouch, I pull the loop through the backside of my belt and run the pouch through the loop. This allows me to both don and doff the pouch without removing my belt.

The contents of the pouch have changed since I first removed them from the waterproof envelope. The Doug Ritter Pocket Survival Pak still forms the base of the pouch, but I’ve added and removed other items to cut down on redundancy and better compliment the other gear that I carry. I also don’t intend the possibles pouch to be strictly a “survival” item. All of the pouch’s contents have utility in a survival situation, but some of them are not intended explicitly for that.

The contents are as follows:

Ferrocerium rod, striker and paracord
Duct tape (26" x 2")
Pencil
Aluminum Foil (3 sq. ft.)
Condom
2 match strikers
8 Coghlan's Emergency Tinder
Sterile stainless steel surgical blade
20mm compass
Stainless steel utility wire (6' of .020")
Signal mirror
Magnifying lens
4 large safety pins
Repair kit
Fishing kit

The components that remain from the Doug Ritter Pocket Survival Pak are the duct tape, pencil, safety pins, 20mm compass, stainless steel utility wire, sterile stainless steel surgical blade, magnifying lens, signal mirror, and aluminum foil. The other items I’ll cover here.

Ferrocerium rod, striker and paracord

This is a standard Light My Fire Scout firesteel and striker. It is not my primary firesteel, but a backup that I can be sure of always having securely attached. You might have noticed that the paracord that I use to secure the rod and striker to the pouch is rather long (about 3.5’). Paracord, of course, has hundreds of uses, so carrying a bit more of it than is strictly necessary isn’t always a bad idea. But the primary reason for the length of this particular piece of cord is that I can use it as a bow string on a fire-bow set.

Condom

This is just one standard latex condom. It can be used as a water carrier, a makeshift glove for a few fingers while taking care of a wound, a barrier to help stop the creation of a new species of half humans half wood nymphs, or utilized in the creation of emergency balloon animals.

Match Strikers

REI Storm Proof Matches always come with 2 spare strikers sealed within a piece of plastic. I find that so-called “strike anywhere” matches can be hit and miss, so by carrying this, I assure myself of always having a dry, reliable surface to strike any kind of match on.

Coghlan's Emergency Tinder

This stuff is not my favorite fire starting tinder, but it does work, and I have a bit of it kicking around, so I tossed it in. They’re stored within a small waterproof bag.

Repair Kit

My repair kit, I think, is somewhat ingenious. I like it, at least. I previously carried a small leather pouch with an assortment of different needles, types of thread, and safety pins. The whole thing was far larger and heavier than I could ever justify it being, so I ditched it and started from scratch. I got the idea for this new kit from the BackpackingLight Forums.

The container is an old Pentel mechanical pencil led refill case. This is the perfect size to secure the two needles I’ve chosen to carry and the case itself is light enough to make me happy. (And it’s free.)

Around the outside of the case, I’ve wrapped a length of black Kevlar thread. When I built this kit, I just wrapped till I got bored, so I have no idea how much thread there is. Enough, I think, for any repairs that I am likely to encounter. I chose Kevlar thread as the best complement of weight and strength. Previously, I carried a bit of standard, thin sewing thread. The thinness of that thread is suitable for sewing things like clothing, but it is decidedly weak. Kevlar thread is the same thickness, not noticeably heavier, but much stronger. I also previously carried a bit of thick waxed nylon string that is appropriate for sewing things like thick leather, heavy cotton canvas, or thick nylon. This is very heavy by my standards and overkill for most repair jobs. Out of all the gear I carry, it would probably be appropriate for repairing only my Kifaru rucksack. And Kifaru rucksacks don’t fail. If by some strange happenstance it did fail, the Kevlar thread would probably be strong enough to get be back home or to some place where a more permanent repair could be made.

Inside the case I carry two needles. One that is thicker and stronger than most thin needles used for the hand-repair of clothing, but still small enough to qualify as small in my eye (just under 5mm in length and thin enough to not punch overly large holes in a thin cotton material). I believe this is the needle that comes with the Doug Ritter Survival Pak, but I could be wrong. The other needle is slightly longer (about 6mm) and has a slightly thicker head, making it more appropriate for heavier material. (I believe this one is technically a sail maker’s needle, but I could be wrong. I have a variety of different needles I’ve picked up over the years and lack the expertise to be able to identify their intended purpose.)

Also inside the case is a small safety pin. The purpose of this is actually just to take up more area inside the case so that the two needles don’t bounce around and make noise.

This repair kit, along with the 4 large safety pins also carried in the possibles pouch, makes for a very small and lightweight repair kit that is able to tackle any of the problems that I may encounter. In addition to this, I also carry a half dozen safety pins of a varying sizes and a couple spare buttons within the rucksack itself. The guts of paracord and the floss in my toiletry kit can also be appropriated as thread.

Fishing Kit

My fishing kit is actually a combination fishing kit and glasses repair kit. An odd combination, you say? I agree.

I am dependent on my glasses, so I have always carried a glasses repair kit. Such kits are available in any drug store in the country and usually consist of a small tube that contains a few of the small screws that most glasses use, a small screwdriver to match, and a couple spare rubber nose pieces.

A year and a half ago I purchased a new pair of glasses that happen to have plastic nose pieces integrated into the frames. Recently, I was going through the possibles pouch, rethinking each item, and came upon the glasses repair kit. I opened it up and was shocked – shocked, I tell you – to discover that it contained two of those small rubber nose piece replacements. With my new glasses, these were completely useless to me. I had been carrying around an extra 2 grams (or so) all this time! I disposed of the offending pieces and felt better immediately.

But then I looked at the tube and its contents and decided that it really was a waste of space. The tube was far too large for the spare screws and screwdriver that it now contained. I shrugged, moved on to looking at the rest of the contents of the possibles pouch, and then had a stroke of brilliance. I would turn the glasses repair kit into a fishing kit!

It follows on the same principle as the repair kit.

Around the outside of the tube, I wrapped a length of 4 lb monofilament fishing line (“ultragreen” in color). Again, I did not measure the length, but it is plenty for such an emergency kit.

Inside the tube, I placed 4 small hooks, 2 split shot, and 2 snap swivels. This is clearly a very minimalist fishing kit, meant for emergencies only, not for when one intends to actually catch fish for a main form of sustenance, but I have used it. It does work.

This particular glasses repair tube is well-suited for such a kit because the lid for the tube is the screwdriver itself. The top of the screwdriver can then be removed, exposing the inside of the hollow handle. It is in here that the spare screws are stored. This allows the glasses repair bit to be separate from the fishing bit.

It should also be noted that the fishing line wrapped around the outside can also be used as repair thread.

Gear List

2009-04-01T00:00:00-07:00

I have refrained from posting gear lists from my travels here mostly out of laziness, but partly because of a fear that they will be taken as absolute. The gear that I pack varies greatly from trip to trip. The type of travel, duration, terrain, and anticipated weather all factor into what I pack. On top of this, I always experiment with different gear and different configurations, seeking the best of both. Thus, my gear will differ even on nearly identical trips.

I should also note that I pack with an eye towards preparedness. That is to say that, for me, the only difference between 3 days and 30 days is the amount of food, and I’m not going to be carrying 30 days worth of food, anyway.

Still, people have expressed interest in what I pack, and I know that I do appreciate it when others whom I respect post their pack lists. So, here is the list from my last trip. The trip was 7 days long, and included about 85 miles of travel on dirt trails, paved roads, and bushwhacking. The route was never what I would call true wilderness or backcountry, meaning that I was always within one days walk of an urban area – and by urban I mean what is probably rural by most standards. The route also took me directly through small towns, which allowed me to restock on food.

I performed the trip over the last week of March. Days got up to around 45 degrees Fahrenheit, with nights around 35. Days were unusually dry (which meant it misted constantly, but didn’t actually rain). During the night, it did rain, but not terribly hard. On the first night, which was at about 1700 feet, it snowed. (The rest of the hike was through valleys and along the coast, so the elevation was well below 1000 feet.) In all, this pack list is a good representation of what I will choose to carry in Winter, not Spring. In the deep, dark of Winter, I will probably carry a few more layers of clothing and switch out some of the lighter garments for heavier ones, but, other than that, this list represents a more-or-less standard pack list for a one week journey in a Cascadian Winter, below elevation.

I do not have a reliable scale, so I cannot weigh my gear. All in all, I’d estimate the pack to be at about 45 lbs.

I’m compiling this list a few days after returning from the trip. I have already unpacked about half the items, so I may have missed something, but the bulk of the gear is certainly here. If you have any questions, or notice any stark absences, feel free to comment. Ideally, I would create a pack list as I’m packing, before the trip. Maybe next time…

The list is subdivided into two sections: what I wore on my body and what I carried in my pack. In the pack section, I decided to separate out what was carried in the lid (called an XTL), which detaches to become a man-purse and so also functions as a sort of escape and evasion bag (or a bail-out bag for the bail-out bag) and the body of the ZXR itself. Otherwise, I have not distinguished between what is carried in the main compartment, the slot pockets, or mounted on the belt. The clothing consists of three main insulating layers: a light wool shirt, a fleece vest, and a lightweight fleece jacket. These three would, of course, alternate between my body and my pack depending on where I was and what I was doing. During most of the hiking, I wore the wool shirt and packed the other two.

Worn On Body

Smartwool Hiking socks
Smartwool Microweight Boxer Briefs
Ibex Woolies long underwear bottoms
Patagonia Capilene Level 2 long sleeve tshirt
Nemesis Hellion neck knife
Atwood Tactical Whistle (worn on paracord around neck)
Railriders Versatac Light pants
- Small bandana
- Ultimate Survival Technologies Strike Force
- K & M Industries Matchcase
- Hair tie
- Bic lighter
The Wilderness Tactical Frequent Flyer belt
- Bushcraft Northwest BCNW-O1 knife
- Leatherman Charge ALX
Pendleton Western lightweight wool shirt
Buff
Filson Tin Cloth Packer Hat
Lowa Renegade Gore-Tex boots
- Sole Ed Viesturs Ultra Cushion footbeds

Kifaru ZXR

Kifaru XTL
- Kifaru Standard Chamber Pocket
  - Rite-in-the-Rain notepad (model 393-M)
  - Lens cloth
  - Hair tie
  - Glasses strap
  - Badger Healing Balm
  - Purell Hand Sanitizer
  - Jetstream ballpoint pen
  - Fisher space pen
  - REI titanium spork
  - 2x spare camera batteries
  - REI keychain thermometer
- Large ziploc
  - Maps (5x)
- Inova 24/7 with head band
- Light My Fire Scout Swedish Firesteel and striker
- Cell phone
- Possibles pouch (Note: I'm not going to discuss the contents of this here, as I'm rethinking it with an eye toward redesign. In it's current incarnation, the items are housed within a TAD Gear SERE SP pouch, which measures 1" deep x 4" tall x 4" wide. It began as a modified Doug Ritter Pocket Survival Pak that I wanted to mount to my belt, instead of carrying it in a pocket. Many of the items remain the same.)
- Joby Gorillapod
- TAD Gear BC-8 pouch
  - Canon Powershot SD1000
- Fallkniven DC4 sharpening stone
- Kleenex pocket pack
- REI Storm Proof matches
- Maxpedition Rollypolly mini dump pouch
- Self Aid Kit (Note: I'm also not going to discuss the contents of this here. Suffice for now, it is a small, pocket-sized kit composed of items in two different small aloksaks)
- Small ziploc bag
- Ultimate Survival Technologies Wetfire cubes (6x)
- Garbage bag (8 gallon)
- Small bandana
- Platypus collapsible bottle (32 oz)
- Outdoor Research Celestial Jacket hardshell
- Integral Designs Sil Poncho/Tarp
REI Peak UL Compact carbon fiber trekking poles
Blackhawk Hellstorm SOLAG gloves
Kershaw folding saw
Cambelback 100oz Omega Resevoir
MSR Hyperflow water filter
Kifaru Paratarp
Big Agnes Seedhouse SL1 Fast Fly Floor
Assorted stakes (12x)
Nite-Ize Figure 9 small (4x)
25ft paracord (6x)
Kifaru Stuff Sack (small)
- Kifaru 20 degree Slick bag
Outdoor Research Hydrolite Pack Sack #1
- Thermarest Prolite 4
Sea-to-Summit Ultra-Sil Dry Sack (8 liters)
- Smartwool Hiking socks (2x)
- Generic cotton boxer briefs
- Ex-Officio Boxer Briefs
- Ibex Outback long sleeve shirt
- TAD Gear Merino long underwear bottoms
- REI synthetic towel, 25" x 15.5" (Note: I bought this a number of years ago and I do not know the specific model name. It does not appear to be the "MultiTowel" currently listed on REI's website.)
TAD Gear Pathfinder fleece hoodie
REI fleece vest (Note: I do not remember the model name and REI no longer sells it. It is made of a light-weight microfleece, with stretchy, spandex-like sides that provide a larger range of movement than a vest of all fleece.)
Trail Designs Ti-Tri Titanium Stove System (900ml pot)
AntiGravity Gear custom pot cozy
Large bandana
Food (Note: this was an assortment of trail mix, couscous, a few energy bars, 2 dry miso packets, 2 bullion cubes, a couple freeze dry meals, 2 tea bags of kukicha, 2 bags of green tea, and one chocolate bar. My journey took me through towns every couple days where I could purchase a meal and supplement my stores with fresh food such as bread, cheese, and fruit. All told, I carried roughly 3 days worth of food at a time.)
REI Nylon Mesh Storage Sack (10" x 6")
- Small comb
- Hair tie
- Nail brush (Note: used not for nails, but for laundry.)
- Floss
- Toothbrush
- Small tube of toothpaste
- Ziploc bag
  - Dr. Bronner's Magic Soap (Almond castile, 2 fl oz.)
Kifaru Standard Chamber Pocket
- Coghlan's Emergency Tinder (6x)
- Sharpie
- Highlighter
- Pencil
- Small repair kit
- Keys
Small plastic bag (Note: used for trash)
Large contractor garbage bag (Note: this bag is large enough to fit over the whole pack. When traveling internationally, I use these to protect all the straps and webbing on the rucksack from the airport conveyor belts. In the wilderness, it can be used internally as a pack liner, externally as a pack cover, or as an emergency bivy.)
Small paperback book (The Golden Spruce by John Vaillant)
TAD Gear BC-8 pouch
- Silva Ranger CL compass
Kifaru GPS pouch
- Garmin Etrex Vista Cx GPS device

Trail Designs Ti-Tri Titanium Stove System

2009-01-18T00:00:00-08:00

I’ve had a few requests to do a review of the new stove system I’ve been using for the past couple weeks. I don’t feel like I have enough experience with it yet to do a proper review, but I snapped some photos today to let people know what it’s all about.

The system is a Trail Designs Caldera Ti-Tri Titanium Stove System. It takes the older (and very popular) Caldera Cone and combines some of the know-how of the folks at Titanium Goat to create a light-weight system that burns alcohol, Esbit tabs, and wood. And, of course, it’s made of titanium.

If you already have a pot you’d like to use, you can contact Trail Designs and have them build a cone for you. Elsewise, the Ti-Tri is available with a pot from Titanium Goat. I’ve previously mentioned my love affair with my Snow Peak Trek 700 mug/cup/pot/thing, but I had been thinking of acquiring a larger, 900ml pot for somewhat more extravagant cooking. Because of this, I decided to get the 900ml Ti-Tri from Titanium Goat, rather than have a Ti-Tri built for my Snow Peak mug.

Titanium Goat’s 900ml pot is a basic affair: handles on the body, a decent lid with a thingy on top that allows it to be easily lifted, as well as three holes for venting or draining water. Titanium Goat claims that the pot and mug weigh in at 4.4oz, which seems correct to me.

The Ti-Tri system itself comes inside of the same caddy system as does the normal Caldera. It’s basically two pieces of plastic that screw together. The diameter of the caddy is the same as a 32oz Nalgene, so it will nest in the same cups (such as the aforementioned Snow Peak 700). This is a somewhat bulky way of carrying the system, I find, but the caddy is constructed out of food grade plastic, so both pieces can double as a bowl or mug. It also does a great job of protecting all the components. So far, I’ve been packing everything in the caddy. I haven’t decided if I’ll keep doing it that way or not.

The alcohol stove that comes with the Ti-Tri is a Trail Designs 12-10 which, they claim, has been designed to “perform optimally with the restricted air flow and higher heat retained by the cone during operation.” My expertise in the design of alcohol stoves are lacking and, as I said before, I don’t feel I yet have enough experience with this system to draw a comparison between it and my Vargo Triad XE (which I also haven’t had for all that long), but the 12-10 has seemed extremely efficient so far (and much easier to light).

The Ti-Tri cone itself is made from a piece of very thin titanium foil. On either side of the cone is a rib – the smaller slides into the larger, and there’s your cone. It’s very easy to assemble. The cone has air vents on the top and the bottom. When assembled, the cone goes over the stove, and the pot nests into the top.

The pot’s lip holds it up. Even with the thinness of the cone’s material, it is a surprisingly sturdy setup. You do have to be somewhat watchful when sliding the pot into the cone, as the pot handle’s mountings will sometimes get caught on the edge of the cone’s opening. I say sometimes, but this actually happens to me the majority of the time. It’s greatly annoying.

If you’re sure to center the handles over the opening in the side of the cone, the handle mountings will not get caught.

The base is an optional addition to the Ti-Tri system to be used for wood burning. It’s simply another piece of titanium foil, slightly larger in diameter than the cone. When burning wood, you set the cone on the base, put the included titanium stakes through the holes in one end of the cone and out the other. These then support the pot higher up, allowing you to shove your fuel in the cone’s side opening.

The Ti-Tri’s third fuel option are esbit tabs, which uses Trail Design’s GramCracker. The GramCracker consists of three pieces of titanium: two sides and a stand. The sides pieces are slid into either side of the stand, which then holds the esbit tab.

This setup directs the heat for a much more efficient burn than that offered by a standard esbit stove. (The GramCracker also comes with a small piece of foil to be used as a base, but since I already carry the larger base for wood burning, I leave this smaller piece at home.) With the GramCracker assembled, the cone is placed on top, and the pot is nested just as with the alcohol stove.

The Ti-Tri also comes with an 8 oz fuel bottle and measuring cup. The measuring cup holds 1 oz and has measurements marked in various units on all sides. The fuel bottle itself is the best I’ve found for alcohol. It has a tight screw lid that prevents any leaking (unlike those little Nalgene dispenser bottles), but also provides a plug with a small hole that allows one to fill the measuring cup (or the stove directly) much easier than it is to pour without such a plug.

Today, I was planning on using the Ti-Tri as an alcohol stove. Trail Designs claims that the Ti-Tri can bring 2 cups of water to a boil with 15ml of alcohol. I’ve found that 15ml brings 2 cups to more of a simmer. For a boil, you’d want 25ml. I didn’t measure exactly how much water I poured into the pot, so I decided to use a bit over 20ml of fuel.

Tea, today, would be Doug Fir and Cedar. After pouring the the fuel from the measuring cup into the stove, I lit the 12-10 with a match, tossed on the cone, settled in the pot (after getting the handle mountings caught on the edge of the cone), and shifted my attentions elsewhere. I didn’t time it this time around, but I think it burned for a bit over 10 minutes. My water was brought to a full, rolling boil – much more than I really needed just for tea, but I was just out for a day-hike, so I wasn’t terribly concerned with fuel conservation. After the burn, I tossed the Doug Fir and Cedar into the pot to steep and settled in for some tea and poetry.

Overall, the Ti-Tri comes in at just under 10oz. It’s not the lightest or most compact alcohol stove setup, but seems to me to be extremely efficient. It’s a bit like the JetBoil of the alcohol stove world. Of course, the Ti-Tri’s primary advantage over other alcohol stoves is that it is not an alcohol stove: it’s an alcohol stove, esbit stove, and wood stove. Having three different fuel options in your pack (and at such a light weight) is quite an invaluable thing. I’m greatly looking forward to further use and testing of what has become my primary cooking system.

The Ti-Tri is a somewhat new product, but has already garnered some positive press, such as a 2008 Backpacking Light Staff Pick. I’m quite curious as to how the system’s wood burning compares to that of the Bush Buddy.

Check out Trail Design’s gallery for photos further photos of the Ti-Tri in use, including at -20 degrees Fahrenheit in the Yukon.

Today’s post brought to you by: that feeling you get when you dangle your legs over a precipice that could probably kill you. And blue skies.

Bed in the bush with stars to see, Bread I dip in the river -- There's the life for a man like me, There's the life for ever. from The Vagabond, Robert Louis Stevenson

Titanium

2008-12-21T00:00:00-08:00

I love titanium. It’s so light, yet strong, and discolors beautifully when burned.

The Snow Peak Trek 700 has been with me on every foray into the wilderness for the past four years, and it’s still going strong. It’s my primary pot/mug/bowl, whether I’m cooking with a fire, canister stove, or alcohol. If I were to create a list of my top ten most valued possessions, I think this would be on it.

I’ve only had the Vargo Triad XE for a few months, but it’s quickly become my favorite stove. It’s far lighter and more versatile than the Esbit stove. I haven’t even looked at my Jetboil since purchasing the Triad. The stove burns both denatured alcohol and fuel tabs, giving it a wider operating potential than most stoves that burn only either one or the other. My experience with alcohol stoves is limited, so I can’t compare the burn efficiency of the Triad to its competitors, but I, so far, have zero complaints.

If there’s the slightest breeze out, the Triad will require a windscreen when burning alcohol (fuel tabs aren’t quite as susceptible). Vargo provides instructions and a diagram for building a windscreen yourself. I ended up purchasing a Trail Designs Vari-Vent windscreen from Anti-Gravity Gear.

BCNW-O1 Bushcraft Knife

2008-11-15T00:00:00-08:00

After a long wait, the end of last week brought with it the arrival of my new BCNW-O1 bushcraft knife.

In late August, I had put aside some money for a new bushcraft knife. For quite some time, I had had my eye on a Skookum Bush Tool. Yet, over the summer I discovered Mike Lummio’s Bushcraft Northwest through his YouTube channel. One of his videos features his knife, the BCNW-O1. It has a very similar design to the slightly larger Skookum, which make it difficult for me to decide which I preferred.

The knife was listed as back-ordered on Mike’s web page, so in the beginning of September I emailed him, asking when the knives would become available. My intention was that I would purchase whichever of the two knives became available first. Mike initially told me 2 weeks. That got delayed to 2 months, due to a batch of special order knives with a sharper grind coming in first and his moving the school to a new location. Still, it was available sooner than the Skookum, so I decided on the BCNW-O1.

It was well worth the wait. I couldn’t be happier with the knife.

(The plus side of the knife being back ordered is that the money had been sitting in a savings account, gaining interest since August.)

As the name implies, the BCNW-O1 is made of O1 tool steel. O1 is a relatively high maintenance material, somewhat soft when compared to other metals such as A2, and more prone to rust if not properly cared for. But the steel can be more easily sharpened to a razor edge than others, and can strike a spark off the backspine with a piece of flint (in addition to the more common ferrocerium rod). Because of this, O1 is quite popular in many bushcraft knives, including the famed Woodlore knife.

The knife is of the classic, Scandinavian design preferred by bushcrafters. The specs, taken from the product page, are as followed:

5/32" (3.9 mm) thick O1 tool steel
RC 59
3 5/8" (9.3cm) Scandi grind blade (grind done by Daniel Koster)
8" (20.3cm) overall length
Full tang

Perhaps the most unique aspect of the knife is the handle. It’s made of bamboo “that has been processed much like micarta. The individual fibers are separated and then bound together under pressure with an industrial strength, formaldehyde-free adhesive. This material can withstand 3,000 psi and is very resistant to the elements while being made from a sustainable resource.” The handle is very smooth, lacking the unique texture of micarta. It feels more like a normal wooden handle, which I love. One of the things that I don’t think is demonstrated very well by the photos on the Bushcraft Northwest site is the size of the handle. It’s a bit bigger and chunkier than what it looks like, which provides for a very comfortable grip. It fits perfectly in my hand.

(While Bamboo can be grown and harvested sustainably, many of the processing methods that go into turning it into clothing are extremely toxic and environmentally destructive. I have no idea about the process that goes into making this handle, but I don’t figure it to be any more environmentally friendly than micarta. Maybe I’m wrong, but I think you should probably avoid any synthetic or processed handle material if you’re concerned about such things.)

In addition the the handle material, the thumb scallops that are carved into either side of the handle are rather unique. This is an excellent feature that assists in certain carving grips, as demonstrated in Mike’s video.

The knife comes with a leather Scandinavian style sheath (available either with or without a firesteel holder) made by JRE Industries. I’ve used one of these with my Mora knives for a couple years and greatly prefer them over any other style I’ve tried.

Most any bushcraft knife made today owes its design, in some part, to Mors Kochanski. Though not as well known as Ray Mears, Kochanski in generally considered to be the father of modern bushcraft. In the spirit of Schwert’s introduction to the Skookum Bush Tool in Outdoors Magazine, I’ll introduce the BCNW-O1 with excerpts from the Knifecraft chapter of Mors Kochanski’s Bushcraft.

The general-purpose bush knife should have a blade as long as the width of the palm, although blades half or twice this length are within acceptable limits. A blade five centimeters long would be an excellent survival knife except for being too small to fall and limb trees of wrist-thickness. A blade 10 to 15 centimeters long will do intricate work like carving a netting needle, yet be large enough to present a good target for a baton when cutting down small trees. A blade 20 centimeters long is a superior tool for heavy work, but awkward to use for fine work.

All general-use knives should have the blade tip close to the profile centerline of the handle. The back of the handle and the back of the blade should be on the same line. The back of the blade should not be thinned down or sharpened so that a baton can be used more effectively without being cut up. There is no advantage to a two-edged blade in bush living.

The blade should be of a good quality carbon steel, from two and a half to three millimeters thick and about two to two and a half centimeters wide. This size of blade is light in weight, yet difficult to break. The steel should be soft enough to be maintained at a shaving edge with common sharpening tools, without frequent sharpening. Such steel is found in Mora (Sweden), Solingen (Germany) or Sheffield (England) knives. Carbon, unlike stainless steel, can be used as the striker in the flint and steel method of fire-lighting. Inexpensive stainless steels have had a bad reputation with respect to producing a keen edge let alone holding it. The Mora stainless steels however, are every bit as good as their carbon steels.

The metal of the knife blade should extend for the full-length of the handle (a full tang) for strength.

The handle should be a durable, water-resistant material that can be shaped to the user's hand if necessary.

The knife should have a strong pommel that will protect the handle if the knife is driven tip first deep into wood.

The curvature of the cutting edge should extend for the full-length of the blade. This cuts well and is one of the best shapes that quickly sharpens to a razor's edge. The knife blade should have a sharp enough point to penetrate deep into wood with a minimum of effort.

The knife handle should be about as long as the width of your palm. A handle that is too thick or too thin fatigues the hand and causes blisters. The cross-section of the handle should be an oval instead of round or rectangular. An oval handle provides an adequate indication of the direction of the cutting edge and raises fewer blisters than handles with angular or rounded corners.

A guard on a bush knife is in the way and detracts from many operations. It prevents the use of a simple, secure deep sheath. Some people prefer a guard for fear of slipping forward onto the knife edge, but unless the knife is used for stabbing, the hand should never slip in this way. In all my years of instructing I do not recall an injury due to the lack of a guard.

The BCNW-O1 clearly meets all of Kochanski’s criteria for the perfect bush knife, as well as introducing new innovations of its own. Though I’ve not had it long enough to perform a full review, I am extremely pleased with the knife. It has exceeded my expectations. I can safely say that I wouldn’t trade it for any other knife.

Additional photos of the knife are on Flickr.

Who Needs Incense

2007-02-25T00:00:00-08:00

Burning-in your newly crafted bow-drill set in the kitchen may not be agreeable to the smoke detector.

But the cedar sure does smell nice.